|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
HIGH CTR, AC INPUT RESPONSE TYPE 4 PIN ULTRA SMALL PACKAGE FLAT LEAD OPTOCOUPLER FEATURES * ULTRA SMALL FLAT-LEAD PACKAGE: 4.6 (L) x 2.5 (W) x 2.1 (H) mm * HIGH CURRENT TRANSFER RATIO: CTR = 200% TYP @ IF = 1 mA, VCE = 5 V * HIGH ISOLATION VOLTAGE BV: 2500 Vr.m.s. * TAPE AND REEL AVAILABLE: PS2915-F3, F4: 3500 pcs/reel PS2915-1 DESCRIPTION The PS2915-1 is an optically coupled isolator containing a GaAs light emitting diode and an NPN silicon phototransistor in one package for high density mounting applications. An ultra small flat lead package has been provided which realizes a reduction in mounting area of about 30% compared with the PS28XX series. APPLICATIONS * DC/DC CONVERTER * MODEM/PC CARD ELECTRICAL CHARACTERISTICS SYMBOLS Transistor Diode VF CT ICEO CTR Coupled VCE(sat) RI-O CI-O tr tf ton ts toff (TA = 25C) PS2915-1 UNITS V pF nA % V pF s s s s s 1011 0.4 5 10 40 10 120 100 200 0.13 MIN 0.9 TYP 1.1 30 100 400 0.3 MAX 1.3 PART NUMBER PARAMETERS Forward Voltage, IF = 1 mA Terminal Capacitance, V = 0, f = 1.0 MHz Collector to Emitter Dark Current, IF = 0 mA, VCE = 40 V Current Transfer Ratio (IC/IF)1, IF = 1 mA, VCE = 5 V Collector Saturation Voltage, IF = 1 mA, IC = 0.2 mA Isolation Resistance, VI-O = 1.0 kVDC Isolation Capacitance, V = 0 V, f = 1.0 MHz Rise Time2, VCC = 5 V, IC = 2 mA, RL = 1 k Fall Time2, VCC = 5 V, IC = 2 mA, RL = 1 k On Time, VCC = 5 V, IF = 1 mA, RL = 5 k Storage Time2, VCC = 5 V, IF = 1 mA, RL = 5 k Off Time2, VCC = 5 V, IF = 1 mA, RL = 5 k Notes: 1. CTR RANK: N: 100 to 400 (%) 2. Test Circuit for Switching Time PULSE INPUT PW = 100 s Duty Cycle = 1/10 In monitor IF 50 VOUT RL = 1 k or 5 k VCC PS2915-1 4 3 1 2 Date Published: August 4, 2005 PS2915-1 ABSOLUTE MAXIMUM RATINGS1 (TA = 25C) SYMBOLS Diode IF IF/C IF (Peak) PD Transistor VCEO VECO IC PC/C PC Coupled BV PT TA TSTG PARAMETERS Forward Current Forward Current Derating Peak Forward Current2 Power Dissipation Collector to Emitter Voltage Emitter to Collector Voltage Collector Current Power Dissipation Derating Power Dissipation Isolation Voltage3 Total Power Dissipation Operating Ambient Temp. Storage Temperature UNITS mA mW/C A mW V V mA mW/C mW Vr.m.s. mW C C RATINGS 50 0.5 0.5 60 40 5 40 1.2 120 2500 160 -55 to +100 -55 to +150 OPTOCOUPLER CONSTRUCTION PARAMETER Air Distance Creepage Distance Isolation Distance UNITS (MIN) 4 mm 4 mm 0.4 mm OUTLINE DIMENSIONS (Units in mm) 2.50.3 4 3 4.60.2 N 1 2 2.1 MAX CAUTIONS REGARDING NOISE: Be aware that when voltage is applied suddenly between the optocoupler's input and outout or between collector-emitters at startup, the output side may enter the on state, even if the voltage is within the absolute maximum ratings. 0.40.1 1.27 0.15 -0.05 +0.1 Notes: 1. Operation in excess of any one of these parameters may result in permanent damage. 2. PW = 100 s, Duty Cycle = 1%. 3. AC voltage for 1 minute at TA = 25 C, RH = 60 % between input and output. 5.00.2 0.20.1 ORDERING INFORMATION (Solder Contains Lead) PART NUMBER PS2915-1-F3 PS2915-1-F4 PACKING STYLE Embossed Tape 3500 pcs/reel TOP VIEW 1. Anode, Cathode 2. Cathode, Anode 3. Emitter 4. Collector ORDERING INFORMATION (Pb-Free) PART NUMBER PS2915-1-F3-A PS2915-1-F4-A PACKING STYLE Embossed Tape 3500 pcs/reel RECOMMENDED MOUNT PAD DIMENSIONS (Units in mm) (0.35) 0.8 0.6 1.27 MARKING 4.14 N -An initial of "NEC" -Assembly lot 1 11 Week assembled Year assembled ( ): Reference value 111 No. 1 pin mark (nicked corner) 24-R0.1 4.7 5.7 15 -Last number of Type No: 15 4.1 MIN PS2915-1 TYPICAL CHARACTERISTICS (TA = 25C, unless otherwise specified) TRANSISTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE Transistor Power Dissipation, PC (mW) 80 140 Maximum Forward Current, IF (mA) 120 100 80 60 40 20 60 40 0.5 mA/C 20 0 25 50 75 100 0 25 50 75 100 125 Ambient Temperature, TA (C) Ambient Temperature, TA (C) FORWARD CURRENTvs. FORWARD VOLTAGE 100 COLLECTOR CURRENT vs. COLLECTOR TO EMITTER VOLTAGE 20 18 CTR = 200 % IF = 5 mA 10 Collector Current, IC (mA) Forward Current, IF (mA) TA = +100C +60C +25C 0C -25C -50C 16 14 12 10 8 6 4 2 1 0.1 2 mA 1 mA 0.5 mA 2 4 6 8 10 0.01 0.0 0.5 1.0 1.5 2.0 0 Forward Voltage, VF (V) Collector to Emitter Voltage, VCE (V) Collector to Emitter Dark Current, ICEO (nA) 10000 COLLECTOR TO EMITTER DARK CURRENT vs. AMBIENT TEMPERATURE 10 COLLECTOR CURRENT vs. COLLECTOR SATURATION VOLTAGE CTR = 200% 5 mA 2 mA 1000 VCE = 20 V 40 V Collector Current, IC (mA) 1 mA 1 100 IF = 0.5 mA 10 1 -25 0 25 50 75 100 0.1 0.0 0.2 0.4 0.6 0.8 1.0 Ambient Temperature, TA (C) Collector Saturation Voltage, VCE(sat) (V) PS2915-1 TYPICAL CHARACTERISTICS (TA = 25C, unless otherwise specified) CURRENT TRANSFER RATIO vs. FORWARD CURRENT VCE = 5 V, n=3 Sample A B C NORMALIZED CURRENT TRANSFER RATIO vs. AMBIENT TEMPERATURE Normalized Current Transfer Ratio, CTR 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -50 Normalized to 1.0 at TA = 25C, IF = 1 mA, VCE = 5 V -25 0 25 50 75 100 500 Current Transfer Ratio, CTR (%) 400 300 200 100 0 0.1 1 10 100 Ambient Temperature, TA (C) Forward Current, IF (mA) SWITCHING TIME vs. LOAD RESISTANCE 10000 IF = 1 mA, VCC = 5 V, CTR = 200 % FREQUENCY RESPONSE Switching Time, t (s) Normalized Gain, GV 1000 toff 0 -5 -10 RL = 1 k 100 100 ts ton -15 300 10 -20 1 1k 10k 100k 1000k -25 0.1 1 10 100 1000 Load Resistance, RL () Frequency, f (kHz) LONG TERM CTR DEGRADATION 1.2 IF = 1 mA 1.0 TA = 25C CTR (relative Value) 0.8 0.6 0.4 0.2 60C 0.0 10 10 2 10 3 10 4 10 5 10 6 Time (Hr) Remark: The graphs indicate nominal characteristics. PS2915-1 TAPING SPECIFICATIONS (Units in mm) Tape Outline and Dimensions 1.75 0.1 2.0 0.5 4.0 0.1 1.55 -0 +0.1 2.9 MAX 12.0 0.2 5.3 0.1 5.3 0.1 2.40.1 1.55 0.05 4.0 0.1 2.9 0.1 Tape Direction PS2915-1-F3 PS2915-1-F4 N N N N Reel Outline and Dimensions 2.00.5 2.0 0.5 13.0 0.2 3302.0 100 1.0 R1.0 21.0 0.8 Packing: 3500 pcs/reel N N N N 13.51.0 11.9 to 15.4 Outer edge of flange PS2915-1 Recommended Soldering Conditions (1) Infrared reflow soldering * Peak reflow temperature * Time of peak reflow temperature * Time of temperature higher than 220 C * Time to preheat temperature from 120 to 180C * Number of reflows * Flux 260 C or below (package surface temperature) 10 seconds or less 60 seconds or less 12030 s Three Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended). Recommended Temperature Profile of Infrared Reflow Package Surface Temperature T (C) (heating) to 10 s 260 C (peak temperature) 220 C to 60 s 180 C 120C 12030 s (preheating) Time (s) (2) Wave soldering * Temperature * Time * Preheating conditions * Number of times * Flux 260 C or below (molten solder temperature) 10 seconds or less 120C or below (package surface temperature) One (Allowed to be dipped in solder including plastic mold portion.) Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended). (3) Cautions * Fluxes USAGE CAUTIONS 1. Protect against static electricity when handling. 2. Avoid storage at a high temperature and high humidity. Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. Avoid removing the residual flux with chlorine-based cleaning solvent after a reflow process. A Business Partner of NEC Compound Semiconductor Devices, Ltd. 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix -A indicates that the device is Pb-free. The -AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL's understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Lead (Pb) Mercury Cadmium Hexavalent Chromium PBB PBDE Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM < 1000 PPM < 100 PPM < 1000 PPM < 1000 PPM < 1000 PPM Concentration contained in CEL devices -A Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL's liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability. |
Price & Availability of PS2915-1-F4-A |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |